- Home
- About us
- Products
- Faqs
- Jacket Manufacturer
- Hoodie & Sweatshirt Manufacturer
- Pants & Bottoms Manufacturer
- T-Shirt & Jersey Manufacturer
- Tracksuit Manufacturer
- Custom Clothing Quality Control
- Streetwear Manufacturer
- Custom Headwear Manufacturer
- OEM/ODM Apparel Manufacturing by Brand Type
- Sweater & Knitwear Manufacturer
- Fabrics & Techniques
- Service Process
- News
- Certificate
- Contact us
What common stitching defects should brands look for in samples?
Look for eight faults, because they account for most rejections: skipped stitches, unbalanced tension, uneven stitch density, seam puckering, seam grin, raw or frayed edges, missing backtack and twisted side seams. All eight are visible in ten minutes if you turn the garment inside out, count stitches over 10 cm and pull the seam by hand.
The eight faults and what causes them
Most stitching defects are machine settings or operator habits, not bad fabric. That matters because a setting can be corrected for the whole lot, while a fabric fault cannot.
| Defect | What you see | Usual cause |
|---|---|---|
| Skipped stitch | Gaps in an otherwise straight seam | Needle size, hook timing, wrong thread for the fabric |
| Unbalanced tension | Loops or a birdnest on one side | Bobbin or upper tension set for a different fabric |
| Uneven stitch density | Stitches run 8 then 12 per inch | Operator speed, feed dog pressure, no guide |
| Seam puckering | Rippled seam line after sewing | Differential feed, damp fabric, too much tension |
| Seam grin | Stitches open and show white when pulled | Low stitch density, thin fabric, no topstitch |
| Raw or frayed edge | Loose threads inside the garment | Edge not overlocked or bound |
| Missing backtack | Seam opens at the start or end | Operator skipped the reverse stitch |
| Twisted side seam | Leg or body spirals when worn | Cutting off-grain or panels mismatched at sewing |
How to check a sample properly
Turn it inside out first. Most of these faults are hidden on the outside by design. Count stitches over 10 cm on the main seams: 10-12 per inch on knits and 8-10 on wovens is the working range, and a seam that varies by more than two stitches along its length will fail in wear.
Then pull the seam across its width with both hands. A seam that opens enough to show the fabric edge, or that feels weak before the fabric itself gives, is a seam grin and will fail at the first wash. Backtack should be 1-1.5 cm at every seam end that carries load.
What we check before a sample ships
Every development sample goes through a 100% inside-out inspection on the first piece, then a documented check on the rest of the set. Seam strength is tested on the main seams and should reach at least 80% of the fabric's tensile strength, so the seam does not become the weak point.
Findings are photographed at the machine, not after the sample is packed, so the operator who made it can see the fault.
Field example
A 500-piece sweatpants order showed skipped stitches at the crotch seam on about 3% of pieces. The cause was a needle that was too fine for the 400 GSM fleece and a thread that was too stiff for the looper. Switching to a 14/90 needle and a softer Tex 40 polyester thread took the rate to 0.4% on the next 200 pieces, with no change to the fabric or the pattern.
Numbers that matter
- Working stitch density: 10-12 per inch on knits, 8-10 per inch on wovens
- Backtack 1-1.5 cm at load-bearing seam ends
- Seam strength target: at least 80% of fabric tensile strength
- Inspect 100% of the first pieces inside out, then sample per AQL